A German-made triplex plunger positive displacement pump with reciprocating plungers for direct or belt drive applications.

Anodized aluminum crankcase with sight glass and vented dipstick; forged, through-hardened, ground and polished crankshaft; bronze connecting rods; hardened stainless steel plunger bases, solid ceramic plungers; nitrile seals (with fabric reinforcing); stainless steel valves and nickel-aluminum-bronze manifold.

Gearbox and bell housings (to connect to gasoline, diesel, electric or hydraulic drive).

WARNING: This product might contain a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

  • P425-3100 Exploded View
  • P425-3100 Parts List
  • P425-3100 Torque Specifications
  • Giant Industries Limited Warranty
  • P425-3100 Installation Instructions
  • P425-3100 Repair Instruction
  • Troubleshooting Guide


U.S. Metric
Flow 10.6 GPM 40.4 L/min
Discharge Pressure (Continuous) 2465 PSI 170 bar
Crankshaft Speed 1450 RPM
Maximum Inlet Pressure 145 PSI 10 bar
Maximum Temperature 86 °F 30 °C
Plunger Diameter 0.98″ 25 mm
Stroke 0.79″ 20 mm
Crankshaft Diameter 28 mm
Crankshaft Rotation Top of Pulley Towards Manifold
Key Width 0.31″ 8 mm
Crankshaft Mounting Either Side
Inlet Ports (2) 3/4″ NPT
Discharge Ports (2) 3/4″ NPT
Crankcase Oil Capacity 30 fl. oz. 0.89 L
Weight 38.6 lbs. 17.5 kg
Key Component Material
Manifold Nickel-Aluminum-Bronze
Plungers Solid Ceramic
Valves 316TI Stainless Steel
Seals Nitrile With Fabric Reinforcing
Gear End Aluminum


Click the image to enlarge


RPM GPM 1000 PSI 1500 PSI 2000 PSI 2465 PSI
750 5.6 3.8 5.7 7.6 9.4
900 6.7 4.6 6.9 9.1 11.3
1010 7.5 5.2 7.7 10.2 12.7
1120 8.3 5.7 8.6 11.4 14.1
1240 9.2 6.3 9.5 12.6 15.6
1450 10.6 7.3 11.0 14.5 18.0

Horsepower Requirements

The ratings shown are the power requirements for the pump. Gas engine power outputs must be approximately twice the pump power requirements shown above.

We recommend a 1.15 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements use the following formulas:
Electric HP = (GPM X PSI)/1450
Gas HP = (GPM X PSI)/1100

*Engine power varies based on horizontal or vertical orientation, as well as by makes and models from each manufacturer.


Plunger Packing Kit – Part #09667
20C 06182 Guide Ring 3
21 07266-0001 O-Ring 3
23 12254 Grooved Seal 3
23B 12255 Grooved Seal 3
24 08376 Support Ring 6
Valve Assembly Kit – Part #09522
27A 08408-0100 Valve Assembly, Complete 6
33 07214-0001 O-Ring, Viton 6
Oil Seal Kit – Part #09641
19 05444 Oil Seal 3

Repair Kits Available

The repair kits listed to the right are available for this pump. If you need further information about these repair kits, or have questions about other specific parts for your pump, please contact you local Giant distributor or contact Giant customer service.

Service & Repair

Giant provides service on each pump and accessory that we sell. Many basic repair procedures are covered in the Giant repair manual. For all other questions on service or repair needs please contact your local Giant distributor.