LP121HT

A German-made reciprocating triplex plunger pump for high temperature applications.

Features:
Spheroidal cast iron crankcase with sight glass and vented dipstick; forged, through-hardened, ground and polished crankshaft; bronze connecting rods; hardened stainless steel plunger bases; solid ceramic plungers; high temperature nitrile seals (with fabric reinforcing); stainless steel valves and cast bronze manifold with coolant tube connections.

WARNING: This product might contain a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

  • LP121HT Exploded View
  • LP121HT Parts List
  • LP121HT Torque Specifications
  • Giant Industries Limited Warranty
  • LP121HT Installation Instructions
  • LP121HT Repair Instructions
  • Troubleshooting Guide

SPECIFICATIONS

U.S. Metric
Flow 17.7 GPM 66.6 L/min
Flow 1059 GPH 4010 L/hr
Maximum Discharge Pressure 1160 PSI 80 bar
Crankshaft Speed 570 RPM
Maximum Inlet Pressure 145 PSI 10 bar
Maximum Temperature 220 °F 105 °C
Plunger Diameter 1.42″ 36 mm
Stroke 1.57″ 40 mm
Crankshaft Diameter 1.26″ 32 mm
Crankshaft Rotation Top of Pulley Towards Fluid End
Crankshaft Mounting Either Side
Inlet Ports 1-1/4″ BSP
Discharge Ports 1″ BSP
Crankcase Oil Capacity 101 fl. oz. 3.0 L
Weight 110 lbs. 50 kg
Key Component Material
Manifold Cast Bronze
Plungers Solid Ceramic Oxide
Valves High Grade Stainless Steel
Seals Nitrile With Fabric Reinforcing
Gear End

Click the image to enlarge


HORSEPOWER SPECIFICATIONS

RPM GPM 300 PSI 600 PSI 900 PSI 1160 PSI
200 6.2 1.3 2.6 3.8 5.0
300 9.3 1.9 3.8 5.8 7.4
400 12.4 2.6 5.1 7.7 9.9
500 15.5 3.2 6.4 9.6 12.4
600 17.6 3.7 7.3 11.0 14.6

Horsepower Requirements

The ratings shown are the power requirements for the pump. Gas engine power outputs must be approximately twice the pump power requirements shown above.

We recommend a 1.15 service factor be specified when selecting an electric motor as the power source. To compute specific pump horsepower requirements use the following formulas:
Electric HP = (GPM X PSI)/1450
Gas HP = (GPM X PSI)/1100


*Engine power varies based on horizontal or vertical orientation, as well as by makes and models from each manufacturer.


REPAIR KITS

ITEM# PART# DESCRIPTION Qty.
Plunger Packing Kit – Part #09310
36 13291 Leakage Seal 3
38 07140 O-Ring 6
40 13199 V-Sleeve 6
Valve Assembly Kit – Part #09196A
44A 07150 O-Ring 9
44B 06266 Support Ring 3
46A 07064 Valve Seat 6
46B 07063 Valve Plate 6
46C 07062 Valve Spring 6
Oil Seal Kit – Part #09571
31A 06118 Oil Seal 3
32A 05596 O-Ring 3
33 06117 Compact Ring 3

Repair Kits Available

The repair kits listed to the right are available for this pump. If you need further information about these repair kits, or have questions about other specific parts for your pump, please contact you local Giant distributor or contact Giant customer service.

PUMP CATEGORIES:
Service & Repair

Giant provides service on each pump and accessory that we sell. Many basic repair procedures are covered in the Giant repair manual. For all other questions on service or repair needs please contact your local Giant distributor.